Gaz 28 P1642 Engine Trouble Code

Powertrain Code P1642

What is Gaz 28 P1642?

Gaz 28 P1642 code can indicate a faulty oxygen sensor, which may eventually damage the catalytic converter (repair cost: $2,000–$2,200). Professional diagnosis costs around $200–$210. Oxygen sensors are often straightforward to replace — check your owner's manual for location and instructions. This issue should be addressed promptly to prevent further damage.

P1642 on the Gaz 28

Owners of the Gaz 28 should be aware that P1642 can appear alongside oil consumption warnings. Low oil pressure caused by a worn PCV system lets crankcase vapour contaminate the mass air flow sensor, sending erroneous readings to the ECU.

P1642 Gaz 28 Engine Diagram

Code Information

Code Type:OBD-II Powertrain (P) Trouble Code
System:Powertrain
Vehicle:Gaz 28
Brand:Gaz
Model:28
Code:P1642

P1642 Gaz 28 Symptoms

⚠️

Check Engine Light

Illuminated Gaz 28 dashboard warning

🔧

Engine Stalling

Engine stops unexpectedly or misfires

⚡

Performance Issues

Reduced power or acceleration on the Gaz 28

🚫

Starting Problems

Difficulty starting the engine

⛽

Poor Fuel Economy

Increased fuel consumption on the Gaz 28

💨

Increased Emissions

Failed emissions test due to P1642

P1642 Code Structure

Understanding what each digit means in the P1642 powertrain trouble code:

P 1 6 4 2
Powertrain Code Fuel And Air Metering Fuel Temperature Sensor B Circuit Range/Performance Injection Pump Fuel Metering Control 'B' High Glow Plug/Heater Circuit 'A' Malfunction

How to Fix Gaz 28 P1642

Diagnostic Steps:

Regarding P1642, carefully inspect the wire harness near the intake manifold bracket, best accessed from below near the oil filter. Look for chafing, pinching, or damaged insulation.

Repair Solution:

Firing order is engineered to minimise vibration. Altering firing order results in mistimed ignition and poor engine operation. Consult vehicle-specific repair manual for correct firing order.

Technical Notes:

P1642 on electronically controlled automatic transmissions relates to shift solenoid operation. The solenoid actuates hydraulic circuits controlling clutches or bands for gear changes.

Gaz 28 P1642 Repair Cost

PCV system overhaul on the Gaz 28 — which resolves oil-mist contamination of the MAF sensor — costs $100–$200. The MAF sensor should be cleaned ($15–$25 DIY) or replaced ($80–$150) at the same time to ensure accurate fuelling after the fix.

P1642 Description

P1642 engine trouble code is related to Glow Plug/Heater Circuit 'A' Malfunction.

Main Cause

The primary reason for P1642 OBD-II Engine Trouble Code is: Fuel Temperature Sensor B Circuit Range/Performance.

Common P1642 Misdiagnosis on the Gaz 28

On Gaz 28 vehicles, the turbo boost solenoid and the MAP sensor feed into the same diagnostic path. P1642 caused by a faulty boost solenoid is sometimes charged to the customer as a MAP sensor replacement, doubling unnecessary parts spend.

DIY Repair Guide: P1642 on Gaz 28

Clearing P1642 on your Gaz 28 with a basic OBD-II reader ($20–$40) is straightforward: plug the reader into the diagnostic port under the dashboard, read the stored code, and clear it. If it returns within one drive cycle, the underlying fault is still present and requires attention.

Preventing P1642 on the Gaz 28

Using only genuine or OEM-specification fuel injectors in the Gaz 28 ensures precise spray pattern and flow rate. Inferior aftermarket injectors are a documented trigger for P1642 through off-target fuel delivery.

Frequently Asked Questions — Gaz 28 P1642

Q: Is P1642 specific to Gaz 28 or does it appear on all cars?
A: P1642 is a standardised OBD-II code that can appear on any make and model. However, the specific components and circuits that trigger this code, and the repair procedures involved, vary significantly between vehicles. The information on this page is focused on the Gaz 28.

Search Another Code